U-Boot 1.1.5 (May 4 2007 - 11:14:56) CPU: ADSP BF532 Rev.: 0.5 Board: IP04 IP-PBX http://www.rowetel.com/ip04.html Clock: VCO: 400 MHz, Core: 400 MHz, System: 133 MHz SDRAM: 64 MB In: serial Out: serial Err: serial 256 MiB DM9000#0 starting from spi flash Hit any key to stop autoboot: 0 Loading from device 0: NAND 256MiB 3,3V 8-bit (offset 0x0) Image Name: uClinux Kernel and ext2 Image Type: Blackfin Linux Kernel Image (gzip compressed) Data Size: 4674491 Bytes = 4.5 MB Load Address: 00001000 Entry Point: 00001000 Automatic boot of image at addr 0x02000000 ... ## Booting image at 02000000 ... Image Name: uClinux Kernel and ext2 Image Type: Blackfin Linux Kernel Image (gzip compressed) Data Size: 4674491 Bytes = 4.5 MB Load Address: 00001000 Entry Point: 00001000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting Kernel at = 1000 Linux version 2.6.19.3-ADI-2007R1-bf1-svn (david@bunny) (gcc version 4.1.1 (ADI 07R1)) #3 Wed May 16 09:46:55 CST 2007 Blackfin support (C) 2004-2006 Analog Devices, Inc. Compiled for ADSP-BF532 Rev. 0.5 Blackfin uClinux support by http://blackfin.uclinux.org/ Processor Speed: 400 MHz core clock and 133 Mhz System Clock Board Memory: 64MB Kernel Managed Memory: 64MB Memory map: text = 0x00001000-0x0018c2b4 init = 0x0018d000-0x0019f14c data = 0x001a1210-0x001e6550 stack = 0x001a2000-0x001a4000 bss = 0x001e6550-0x002194a4 available = 0x002194a4-0x03200000 rootfs = 0x03200000-0x03f00000 DMA Zone = 0x03f00000-0x04000000 Instruction Cache Enabled Data Cache Enabled (write-through) Hardware Trace Enabled Built 1 zonelists. Total pages: 12700 Kernel command line: root=/dev/mtdblock2 rw ethaddr=02:80:ad:20:31:b8 Configuring Blackfin Priority Driven Interrupts PID hash table entries: 256 (order: 8, 1024 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Physical pages: 3200 Memory available: 48408k/63867k RAM, (72k init code, 1580k kernel code, 203k data, 1024k dma) Blackfin Scratchpad data SRAM: 4 KB Blackfin Instruction SRAM: 32 KB Security Framework v1.0.0 initialized Capability LSM initialized Mount-cache hash table entries: 512 NET: Registered protocol family 16 Blackfin GPIO Controller Blackfin DMA Controller bf1_init(): chip_id=527A50CB,dspid=E5040005 bf1_init(): registering device resources SCSI subsystem initialized NET: Registered protocol family 2 IP route cache hash table entries: 512 (order: -1, 2048 bytes) TCP established hash table entries: 2048 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 2048 bind 1024) TCP reno registered yaffs May 14 2007 16:40:33 Installing. io scheduler noop registered io scheduler anticipatory registered (default) io scheduler cfq registered Dynamic Power Management Controller Driver v0.1: major=10, minor = 254 Serial: Blackfin serial driver bfin-uart.1: ttyBF0 at MMIO 0xffc00400 (irq = 21) is a BFIN-UART RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize dm9000 Ethernet Driver eth0: dm9000 at 20100000,20100002 IRQ 48 MAC: 02:80:ad:20:31:b8 BF5xx flash: probing 16-bit flash bus for cfi_probe BF5xx flash: probing 16-bit flash bus for smt_flash BF5xx flash: probing 16-bit flash bus for jedec_probe uclinux[mtd]: RAM probe address=0x3200000 size=0xd00000 Creating 1 MTD partitions on "RAM": 0x00000000-0x00d00000 : "ROMfs" uclinux[mtd]: set ROMfs:EXT2 to be root filesystem Generic platform RAM MTD, (c) 2004 Simtec Electronics NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Unknown NAND 256MiB 3,3V 8-bit) Scanning device for bad blocks Bad eraseblock 732 at 0x05b80000 Creating 2 MTD partitions on "NAND 256MiB 3,3V 8-bit": 0x00000000-0x00800000 : "linux kernel" 0x00800000-0x10000000 : "file system" Zapata Telephony Interface Registered on major 196 Zaptel Version: SVN-trunk-r1501 Echo Canceller: MG2 Code test: code function addr = 0x000f0aac dma_alloc_init: dma_page @ 0x003fe000 - 256 pages at 0x03f00000 port: 1 port_type: O port: 2 port_type: O port: 3 port_type: S port: 4 port_type: S port: 5 port_type: - port: 6 port_type: - port: 7 port_type: - port: 8 port_type: - Module 0: Installed -- AUTO FXO (FCC mode) Module 1: Installed -- AUTO FXO (FCC mode) reg 0: 0x5 reg 14: 0x0 reg 74: 0x32 reg 80: 0x0 reg 81: 0x0 reg 92: 0xff reg 82: 0xc9 reg 83: 0xc8 reg 0: 0x5 reg 14: 0x0 reg 74: 0x32 reg 80: 0x0 reg 81: 0x0 reg 92: 0xff reg 82: 0xcb reg 83: 0xca Start manual calibration Module 2: Installed -- MANUAL FXS reg 0: 0x5 reg 14: 0x0 reg 74: 0x32 reg 80: 0x0 reg 81: 0x0 reg 92: 0xff reg 82: 0xc8 reg 83: 0xc7 reg 0: 0x5 reg 14: 0x0 reg 74: 0x32 reg 80: 0x0 reg 81: 0x0 reg 92: 0xff reg 82: 0xc9 reg 83: 0xc9 Start manual calibration Module 3: Installed -- MANUAL FXS Found: Blackfin STAMP (8 modules) wcfxs_init_ok = 1 TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 yaffs: dev is 32505858 name is "mtdblock2" yaffs: Attempting MTD mount on 31.2, "mtdblock2" yaffs: auto selecting yaffs2 block 669 is bad VFS: Mounted root (yaffs filesystem). Freeing unused kernel memory: 72k freed (0x18d000 - 0x19e000) devpts: called with bogus options mount: mounting /dev/mtdblock2 on /mnt/flash failed mount: mounting /dev/mtdblock5 on /mnt/spiflash failed mount: mounting /dev/mmc on /mnt/mmc failed mount: mounting /dev/mmc1 on /mnt/mmc1 failed mount: mounting /dev/uba on /mnt/uba failed mount: mounting /dev/uba1 on /mnt/uba1 failed mount: mounting /dev/sda on /mnt/sda failed mount: mounting /dev/sda1 on /mnt/sda1 failed We already have unpacked Asterisk configuration... rm: cannot remove '/defaults.tgz': No such file or directory kill(pid=34, sig=0) returned -1 Blackfin dm9000 interrupt setup: DEMUX_GPIO irq 48 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 mount: mounting /dev/sda1 on /var/lib/asterisk/sounds failed mv: cannot rename '/bin/gui_custommenus.conf': No such file or directory ntpdate: not found Registered tone zone 0 (United States / North America) Starting Asterisk... Welcome to: ____ _ _ / __| ||_| _ _ _ _| | | | _ ____ _ _ \ \/ / | | | | | | || | _ \| | | | \ / | |_| | |__| || | | | | |_| | / \ | ___\____|_||_|_| |_|\____|/_/\_\ |_| IP04 IP-PBX For further information see: http://www.rowetel.com/ucasterisk/ip04.html Thanks to the Astfin & BlackfinOne teams, Analog Devices & the Asterisk community. BusyBox v1.4.1 (2007-05-15 13:42:25 CST) Built-in shell (msh) Enter 'help' for a list of built-in commands. root:~> df Filesystem 1k-blocks Used Available Use% Mounted on /dev/mtdblock2 253952 12080 241872 5% / root:~> cat /proc/mtd dev: size erasesize name mtd0: 00d00000 00001000 "ROMfs" mtd1: 00800000 00020000 "linux kernel" mtd2: 0f800000 00020000 "file system"